VESPA LX Series User Manual Download

Page: 118 / 272

STANDARD COUPLING CLEARANCE

Name

Description

Dimensions

Initials

Quantity

Top piston ring

0.025 to 0.070

Middle piston ring

0.015 to 0.060

oil scraper

0.015 to 0.060

MAXIMUM ADMITTED CLEARANCE AFTER USE

Name

Description

Dimensions

Initials

Quantity

Top piston ring

0.080 mm

Middle piston ring

0.070 mm

oil scraper

0.070 mm

Removing the piston

- Install piston and wrist pin onto the connecting

rod, aligning the piston arrow the arrow facing to-

wards the exhaust.

- Fit the pin retainer ring onto the appropriate tool.

Specific tooling

020430Y

Pin lock fitting tool

- With the opening in position indicated on the tool,

take retainer ring in the closed position using the

punch.

- Fit the wrist pin snap ring using the plug as shown

in the figure

N.B.

THE TOOL FOR INSTALLING THE RETAINER RINGS MUST
BE USED MANUALLY.

CAUTION

USING A HAMMER TO POSITION THE RINGS CAN DAM-
AGE THE LOCKING HOUSING.

Engine

Vespa LX 125 - 150 i.e.

ENG - 118

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands