VESPA LX Series User Manual Download

Page: 92 / 272

This section describes the operations to be carried out on the engine and the tools to be used.

Automatic transmission

Transmission cover

- To remove the transmission cover it is necessary

to remove the rear plastic cover first by inserting a

screwdriver in the corresponding slotted holes.

Using the clutch bell lock wrench, remove the driv-

en pulley axle locking nut and recover the washer.

- Remove the cap/dipstick from the engine oil filling

hole.

- Remove the ten screws.

- Remove the transmission cover. If this operation

is performed directly on the vehicle, it is necessary

to remove the cooling air sleeve and the three air

filter housing retainers.

Specific tooling

020423Y

Driven pulley lock wrench

Air duct

- Unscrew the Torx screws fixing the air duct bulk-

head and remove the bulkhead.

- Remove the 3 screws, then take out the manifold

as well as the filter.

Engine

Vespa LX 125 - 150 i.e.

ENG - 92

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands