manualshive.com logo in svg

VESPA LX Series, User Manual

The Philips LX Series offers a range of innovative entertainment systems designed to enhance your audiovisual experience. With crystal-clear sound and stunning visuals, these products provide an immersive entertainment experience. Download the user manual for free from manualshive.com to make the most of your Philips LX Series product.

Share
Download
background image

- Using a feeler dial gauge and the magnetic base,

measure the bell eccentricity.

- Repeat the measurement in 3 positions (Central,

internal, external).

- If faults are found, replace the bell.

Specific tooling

020074Y

 

Support base for checking crankshaft

alignment

020335Y

 

Magnetic mounting for dial gauge

Characteristic

clutch bell inspection: Limit eccentricity.

Admissible limit eccentricity: 0.15 mm

Removing the clutch

- Prepare the locking tool for the driven pulley with

the pins half-screwed in the tool set to «

C

».

- Introduce the adapter ring 11 with the chamfering

facing the inside of the tool.

- Fit the driven pulley unit in the tool so as the bolt

get into the masses clutch support holes. After-

wards make the support screw make contact with

a minimum force.

- Using the specific wrench, inserted 46 mm from

the side, remove the clutch central locking nut.

- Separate the driven pulley into its components (clutch with fan and contrast spring with plastic fittings).

CAUTION

THE TOOL MUST BE FIRMLY FIXED IN THE VICE AND THE CENTRAL SCREW MUST NOT BE
TIGHTENED WITH EXCESSIVE TORQUE AS THIS MAY DAMAGE THE PULLEY OR DEFORM THE
SPECIFIC TOOL.

Specific tooling

020444Y

 

Tool for fitting/ removing the driven pulley clutch

020444Y011

 

adapter ring

Vespa LX 125 - 150 i.e.

Engine

ENG - 95

Summary of Contents for LX Series

















































































































































































































































































Reviews:

No comments

Related manuals for LX Series

JDbug GS300 Owner'S Manual preview
GS300
Brand: JDbug Pages: 8
DAELIM BESBI - Brochure preview
BESBI -
Brand: DAELIM Pages: 2
E-Wheels EW-01 Owner'S Manual preview
EW-01
Brand: E-Wheels Pages: 16
E-TRENDS FLY Assembly Instructions Manual preview
FLY
Brand: E-TRENDS Pages: 15
Rascal Vecta Sport Owners Manual & Service Record preview
Vecta Sport
Brand: Rascal Pages: 32
Denver SCO-85351 THOR User Manual preview
SCO-85351 THOR
Brand: Denver Pages: 25
E-Glide D 150 Manual preview
D 150
Brand: E-Glide Pages: 9
EMG VELOCIPTOR EVO ES 88E User Manual preview
VELOCIPTOR EVO ES 88E
Brand: EMG Pages: 36
Moma self-balance User Manual preview
self-balance
Brand: Moma Pages: 11
Brigmton BBOARD-60-N-A-R Instruction Manual preview
BBOARD-60-N-A-R
Brand: Brigmton Pages: 22
DAELIM NS125III - SERVICE Service Manual preview
NS125III - SERVICE
Brand: DAELIM Pages: 203
Speedlion 84036 Quick Start Manual preview
84036
Brand: Speedlion Pages: 9
Hudora 14124 Instructions On Assembly And Use preview
14124
Brand: Hudora Pages: 28
Daymak Boomerbugy II Owner'S Manual preview
Boomerbugy II
Brand: Daymak Pages: 32
Handicare ANTIBES User Manual preview
ANTIBES
Brand: Handicare Pages: 64
Medicare Technology Regatta Owner'S Manual preview
Regatta
Brand: Medicare Technology Pages: 21
Urban XZ-E010 User Manual preview
XZ-E010
Brand: Urban Pages: 14
BOWHEAD REACH Owner'S Manual preview
REACH
Brand: BOWHEAD Pages: 38

Brands by name

Popular brands

Load more brands