VESPA LX Series User Manual Download

Page: 68 / 272

With the ignition key switch at ON check there is

battery voltage between the Red-White and Black

cables

With MIU connector disconnected, check the con-

tinuity between the Orange-White cable and pin 7

of the interface wiring.

Specific tooling

020481Y

Control unit interface wiring

020331Y

Digital multimeter

Virgin circuit

When the ignition system is not encrypted, any key

will start the engine but limited to 2000 rpm. The

keys can only be recognised if the control unit has

been programmed properly.

The data storage procedure for a previously un-

programmed control unit provides for the recogni-

tion of the red key (master key) as the first key to

be stored to memory: this becomes particularly

important because it is the only key that enables

the control unit to be wiped clean and reprogram-

med for the memorisation of the service keys.

Electrical system

Vespa LX 125 - 150 i.e.

ELE SYS - 68

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands