VESPA LX Series Page 121 User Manual Download

Page: 121 / 272

- Remove the central screw and the tensioner

spring. Check that the one-way mechanism is not

worn.

- Check the condition of the tensioner spring.

- If examples of wear are found, replace the whole

unit.

Inspecting the valve sealings

- Measure the width of the sealing surface on the valve seats.

VALVE SEAL SURFACE

Specification

Desc./Quantity

Intake valve - seal surface

2.4 to 2.8 mm

Exhaust valve - seal surface

2.2 to 2.6 mm

Inspecting the valve housings

- Remove any carbon formation from the valve guides.

- Measure the inside diameter of each valve guide.

- Take the measurement at three different heights in the rocker arm push direction.

Characteristic

Standard drainage guide diameter

5.012 mm

Standard inlet guide diameter

5.012 mm

Vespa LX 125 - 150 i.e.

Engine

ENG - 121

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands