VESPA LX Series User Manual Download

Page: 115 / 272

Removing the valves

- Using the specific tool fitted with the element

shown in the figure, remove the cotters, the plates

and the spring between the valves.

Specific tooling

020382Y

Valve cotters equipped with part 012

removal tool

020382Y011

adapter for valve removal tool

- Remove the oil seals with the appropriate tool.

- Remove the lower spring supports.

Specific tooling

020431Y

Valve oil seal extractor

Removing the cylinder - piston assy.

- Remove the chain guide pad.

- Remove the cylinder base gasket.

CAUTION

TO AVOID DAMAGING THE PISTON, SUPPORT IT WHILE
REMOVING THE CYLINDER.

- Remove the two retainer rings, the wrist pin and

the piston.

- Remove the 3 piston rings from the piston.

N.B.

BE CAREFUL NOT TO DAMAGE THE PISTON RINGS DUR-
ING REMOVAL.

Vespa LX 125 - 150 i.e.

Engine

ENG - 115

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands