VESPA LX Series User Manual Download Page 195

Page: 195 / 272

Refitting

To refit, carry out the removal operations in reverse order, observing the prescribed tightening torques.

Locking torques (N*m)

shock absorber lower clamping

20 - 27

shock absorber upper clamp

20 to 30

Shock-absorber - calliper bracket

Removal

- Remove the front wheel hub with the brake disc

- Remove the front shock absorber lower clamps

- Remove the bracket locking Seeger ring

- Unscrew the bracket

- Before refitting the bracket in the wheel axle,

place the O-ring as shown in the photograph so

that it is correctly placed after fitting the bracket.

- Refit the washer and the Seeger ring.

- Refit the lower screws fixing the shock absorber

to the bracket and tighten at the prescribed torque

Locking torques (N*m)

Shock absorber lower clamping

20 to 27

Vespa LX 125 - 150 i.e.

Suspensions

SUSP - 195

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Brands by name

Popular brands