VESPA LX Series User Manual Download

Page: 197 / 272

- Assemble a new roller bearing on the shock ab-

sorber side and move it until it stops using the

specific tool

Specific tooling

020036Y

Punch

- Suitably hold the brake calliper - shock absorber

attachment bracket

- Assemble a new roller bearing on the wheel hub

side and move it until it stops using the specific tool

Specific tooling

020037Y

Punch

Refitting

- Refit the parts in reverse order of the removal

operation.

CAUTION

BEFORE CARRYING OUT REFITTING OPERATIONS IN
THE AREAS MARKED WITH AN ASTERISK, LUBRICATE
THEM WITH THE RECOMMENDED PRODUCT

Specific tooling

020036Y

Punch

020037Y

Punch

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

Steering bearing

Removal

- Use the specific tool both to remove the lower seat of the upper bearing and to remove the upper seat

of the lower bearing fitted on the chassis.

Vespa LX 125 - 150 i.e.

Suspensions

SUSP - 197

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands