VESPA LX Series User Manual Download Page 102

Page: 102 / 272

- Remove the belt and slide the movable half-pul-

ley with the relevant bush, taking care of the falling

free assembled rollers.

- Remove the return rollers plate with the relative

guide pads.

Inspecting the rollers case

- Check that the internal bushing is not abnormally worn and measure inner diameter.

N.B.

DO NOT LUBRICATE OR CLEAN THE BUSHING.

BUSHING ROLLER CONTAINER

Specification

Desc./Quantity

Maximum allowable diameter

Ø 26.121 mm

Standard diameter

Ø 26+0 +0.021 mm

BUSH SLIDE PULLEY

Specification

Desc./Quantity

Minimum diameter permitted

Ø 25.950 mm

Standard diameter

Ø 26-0.020 -0.041 mm

VARIABLE SPEED ROLLERS

Specification

Desc./Quantity

Minimum diameter permitted

Ø 18.5 mm

Standard diameter

Ø 26±0.1 mm

Engine

Vespa LX 125 - 150 i.e.

ENG - 102

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Brands by name

Popular brands