manualshive.com logo in svg

VESPA LX Series, User Manual

The Philips LX Series offers a range of innovative entertainment systems designed to enhance your audiovisual experience. With crystal-clear sound and stunning visuals, these products provide an immersive entertainment experience. Download the user manual for free from manualshive.com to make the most of your Philips LX Series product.

Share
Download
background image

Removing the hub bearings

- Check the state of the bearings being examined

(wear, clearance and noisiness). If faults are de-

tected, do the following.

- Use the specific bearing extractor to remove the

three 15 mm bearings (2 in the crankcase and 1 in

the hub cover).

Specific tooling

001467Y009

 

Driver for OD 42-mm bearings

001467Y013

 

Pliers to extract ø 15-mm bearings

Removing the wheel axle bearings

- Take out the clip on the outside of the gearbox

cover.

- Remove the bearing with the adequate tools ad-

equately supporting the hub cover, as shown in the

figure.

Specific tooling

020376Y

 

Adaptor handle

020364Y

 

25-mm guide

With the appropriate tools, remove the oil seal as

shown in the figure.

Specific tooling

020376Y

 

Adaptor handle

020359Y

 

42x47-mm Adaptor

Removing the driven pulley shaft bearing

If it is necessary to remove the driven pulley shaft, from the relevant bearing and oil seal, remove driven

pulley.

- Extract the driven pulley shaft from its bearing.

- Remove the oil seal using a screwdriver, working from inside the bearing and being careful not to

damage the housing, make it come out of the belt transmission side.

- Remove the Seeger ring shown in the figure

Vespa LX 125 - 150 i.e.

Engine

ENG - 105

Summary of Contents for LX Series

















































































































































































































































































Reviews:

No comments

Related manuals for LX Series

Denver SCO-85351 THOR User Manual preview
SCO-85351 THOR
Brand: Denver Pages: 25
Ebikes-Canada EBC-S18 User Manual preview
EBC-S18
Brand: Ebikes-Canada Pages: 34
B+B FORTIS Instruction Manual preview
FORTIS
Brand: B+B Pages: 36
Dynacraft 8004-57 Owner'S Manual preview
8004-57
Brand: Dynacraft Pages: 13
Texas Comfort 125-4X User Manual preview
Comfort 125-4X
Brand: Texas Pages: 33
Whirlwind C4 Manual preview
C4
Brand: Whirlwind Pages: 14
Whirlwind K5 Manual preview
K5
Brand: Whirlwind Pages: 16
V&D Electric Bikes Go-Bike Q1 User Manual preview
Go-Bike Q1
Brand: V&D Electric Bikes Pages: 28
Derby cycle Pedelec Integrale 0.5 Original User Manual preview
Pedelec Integrale 0.5
Brand: Derby cycle Pages: 64
Active Mobility xtaga Impala User Manual preview
xtaga Impala
Brand: Active Mobility Pages: 26
Tern Vektron S10 User Manual preview
Vektron S10
Brand: Tern Pages: 102
Promovec Element Instruction Manual preview
Element
Brand: Promovec Pages: 16
Scootacar Comfi-Car User Manual preview
Comfi-Car
Brand: Scootacar Pages: 19
Macwheel MX1 User Manual preview
MX1
Brand: Macwheel Pages: 20
E-TON Beamer R4 Owner'S Manual preview
Beamer R4
Brand: E-TON Pages: 27
E-Wheels E2S V2 User Manual preview
E2S V2
Brand: E-Wheels Pages: 70
kikkaride DUSTY Instructions For Use Manual preview
DUSTY
Brand: kikkaride Pages: 23
UFREE SCOOTER FS-E31 Quick Manual preview
FS-E31
Brand: UFREE SCOOTER Pages: 12

Brands by name

Popular brands

Load more brands