VESPA LX Series User Manual Download

Page: 106 / 272

With the sectional punch, remove the driven pulley

shaft bearing.

Specific tooling

020376Y

Adaptor handle

020375Y

28 x 30 mm adaptor

020363Y

20-mm guide

See also

Removing the driven pulley

Inspecting the hub shaft

- Check the three shafts for wear or distortion of

the toothed surfaces, the bearing housings, and

the oil seal housings.

- In case of anomalies, replace the damaged com-

ponents.

Inspecting the hub cover

- Check that the fitting surface is not dented or distorted. - Check the capacity of the bearings and the

brake camshaft. - If faults are found, replace the hub cover.

Refitting the driven pulley shaft bearing

- Heat up the parts using the specific heat gun

Specific tooling

020150Y

Air heater mounting

020151Y

Air heater

- Reassemble the driven pulley axle bearing positioning it with ball bearing in view from the inside of

the hub cover using the adequate tools

Specific tooling

020376Y

Adaptor handle

Engine

Vespa LX 125 - 150 i.e.

ENG - 106

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands