VESPA LX Series Page 165 User Manual Download

Page: 165 / 272

Check the presence of fixed voltage between the

grey/black cable of the remote control base and

ground. If there is not, check the continuity of the

Grey/Black cable between the fuse box (No. 6, 15

A) and the remote control base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT WITH THE
COMPONENTS DISCONNECTED. (REMOTE CONTROLS,
CONTROL UNIT, FUSES ETC.).

pump circuit 6

Check, on switching to "ON", that there is battery

voltage, for about two seconds, to the Black-Green

cable of the pump connector and ground with

pump connector disconnected. Otherwise, check

the continuity of the Black-Green cable between

the pump connector and the remote control base.

Check the efficiency of the ground line of the fuel

pump by measuring the continuity between the

pump connector black cable, system side, and the

ground.

If, when switching to "ON", the pump continues to

turn after two seconds of activation, check, with the

control unit disconnected and the injection load re-

Vespa LX 125 - 150 i.e.

Injection

INJEC - 165

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands