Veeder-Root TLS-450 Setup And Operation Download Page 77 | Manualshive

Page: 77 / 408

Veeder-Root TLS-450 Setup And Operation Download Page 77

TLS-450 Setup and Operation Screens Manual

66

Pump Threshold (%)

This feature is for line manifolded tanks and is only enabled when you have the Dispense Mode set to
Manifolded:Sequential (See Setup/Pumps and Lines/Lines). When the tank's volume drops below the
entered Pump Threshold percentage, pumping will switch over immediately to the next available tank in
the line manifolded set. Pumping will continue from the current tank for another 10 seconds to avoid a
disruption in dispensing during the switch over.

Allowable entry: 0.00 to 50.00% (of the tank's full volume)
Default: 10.00%

Stick Offset Fuel

Allowable entry: -144 to +144 in (-3657.60 to 3657.60 mm)
Default: 0

Stick Offset Water

Allowable entry: -144 to +144 in (-3657.60 to 3657.60 mm)
Default: 0

Delivery Delay

Enter the number of minutes to wait after the Console determines that a Delivery is complete.

This delay period can prevent false Alarms and Warnings due to turbulence in the Tank caused by
Deliveries.

Allowable entry: 1 to 99 minutes
Default: 1

Gross Test Fail

The Gross Test Fail feature allows you to disable or enable an alarm that triggers when a 3.0 gph
(11.3lph) leak test fails.

Allowable selections: Enabled or Disabled
Default: Enabled

Periodic Test Fail

The Periodic Test Fail feature allows you to disable or enable an alarm that triggers if a 0.2 gph (0.76lph)
leak test fails.

Allowable selections: Enabled or Disabled
Default: Enabled

Annual Test Fail

The Annual Test Fail feature allows you to disable or enable an alarm that triggers when an 0.1 gph
(0.38lph) leak test fails.

Allowable selections: Enabled or Disabled
Default: Disabled

«
...
75
76
77
78
79
...
»

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands