manualshive.com logo in svg

Veeder-Root TLS-450, Setup And Operation

Share
Download
Veeder-Root TLS-450 Setup And Operation Download Page 311

TLS-450 Setup and Operation Screens Manual 

 

300 

 

•

 

Containment Sump 

Sample Counter 

Sensor Sample Counter value 
 
Value range: 0 to 99 

Value 

Resistance or current value 
 
Value range: 0 to 1000000000 (Resistance Value) or 0.0 to 50.0 (Current Value in microamps) 

Status 

Sensor Status 
 
Possible messages: 

•

 

Normal  

•

 

Unknown  

•

 

Setup Data Warning  

•

 

Fuel Alarm  

•

 

Out Alarm  

•

 

Short Alarm  

•

 

Water Alarm  

•

 

Water Out Alarm  

•

 

High Liquid Alarm  

•

 

Low Liquid Alarm  

•

 

Liquid Warning 

 

Sensor Diagnostics 2-Wire CL Sensor Refresh Rate 

The 2-Wire CL Sensor Diagnostics data will be refreshed every 5 seconds. 
 

Control Button (right of screen) 

Setup 

 

Touch this button open the 

Device Setup – Type A Sensor (2-Wire CL)

 screen. 

 
 
 

Summary of Contents for TLS-450

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands