VDO CONTISYS OBD - V3.0 Instruction Manual Download Page 24

Page: 24 / 144

FastCheck

WARNING: Electronic Parking Brake (EPB) safety

• Ensure that you are fully familiar with the braking system and its operation

before commencing any work.

• The EPB control system may be required to be deactivated before carrying out

any maintenance/diagnostic work on the brake system. This can be done from
the service tool menu.

• Only carry out maintenance work when the vehicle is stationary and on level

ground.

• Ensure that the EPB control system is reactivated after the maintenance work

has been completed.

Note:

Continental Trading GmbH accept no responsibility for any accident or injury

arising from the maintenance of the Electronic Parking Brake system.

Summary of Contents for CONTISYS OBD - V3.0

















































































































































Search results

Summary of Contents for CONTISYS OBD - V3.0

Reviews:

Related manuals for CONTISYS OBD - V3.0

Brands by name

Popular brands

VDO CONTISYS OBD - V3.0, Instruction Manual

Search results

Summary of Contents for CONTISYS OBD - V3.0

Reviews:

Related manuals for CONTISYS OBD - V3.0

Brands by name

Popular brands