background image

FastCheck

34

FastCheck EPB

Connection

Using the Vehicle Application List, identify the required interface cable for the vehicle 
system to be tested. Connect the cable to the service tool and secure the fixing 
screws.

If using the EOBD (J1962) pin-switchable cable (A2C59512073), ensure the settings 
on the switch box correspond to the settings listed for the vehicle and system being 
tested.

WARNING: Incorrect settings on the switch box may cause irreparable damage to 
the vehicle's electrical system.

Ensure the vehicle's ignition is OFF.

Connect the service tool to the required vehicle connector, refer to 

‘Diagnostic 

connector locations’, page 79

, for further information. 

Power for the service tool is provided by the vehicle connector. Once connected, the 
service tool will perform an internal self test and then the screen will display the version 
of the current software before displaying the main menu.

Use the 

 and 

 keys to select the 'FastCheck EPB' application and press 

 to 

confirm the selection. To return to the previous menu, press the 

 key.

Turn the vehicle's ignition ON.

Use the 

 and 

 keys to select the vehicle manufacturer and press 

 to confirm 

the selection.

MAIN MENU

1.

EOBD

2.

FastCheck ABS

3.

FastCheck Airbag

4.

FastCheck Climate

5.

FastCheck EPB

6.

FastCheck SAS

7.

FastCheck Service

8.

FastCheck TPMS

9.

User Menu

A

B

C

D

E

F

G

H

I

J

K

L

1

2

3

4

5

6

7

8

9

10

11

12

CON0017

Summary of Contents for CONTISYS OBD - V3.0

















































































































































Reviews: