Vaisala IRIS User Manual Download Page 344

Page: 344 / 394

2. Configure output to the TDWR/LLWAS Integrator:

a. Use IRIS setup/output to configure the output to the Integrator.

See the following example. Use the

Short

file name format.

Since the Integrator runs on the same machine, use

Copy

rather than

RCP

(remote

copy).
The notification port must match that configured for the Integrator in the

runways.conf

file (See

Configuring Integrator and Runways Utility - runways.conf

(page 354)

). The recommended port is 30726 as shown in the example.

b. Configure the

IRIS Product Output Menu

to make automatic output of

SHEAR

and

SLINE

products to the Integrator.

See

Sending a Product to a Device (page 266)

D.7 Ribbon Displays

A busy ATC controller does not have time to look at color situation displays and interpret
them.

IRIS Product and Display User Guide

M211319EN-H

342

RESTRICTED

Summary of Contents for IRIS











































































































































































































































































































































































































Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands

Vaisala IRIS, User Manual

Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands