Unipulse TM700 Operation Manual Download Page 40

Page: 40 / 91

SETTING OF FUNCTIONS

Chapter

5-9.

Comparison Functions

Set the HI/LO limit of torque and rotation speed. (Hold synchronized)

≪

Setting value

≫

- Torque

HI limit/LO limit:

-99999 to 99999

- Rotation speed

HI limit/LO limit:

0 to 99999

＜

HI/OK/LO output conditions

＞

- HI

Indicated value

＞

HI limit

- LO

Indicated value

＜

LO limit

- OK

LO limit

≦

Indicated value

≦

HI limit

Overload of the torque and rotation speed is monitored. (Hold not synchronized)
When they exceed the alarm HI limit or fall below the alarm LO limit, the external output "ALM"
turns ON.

≪

Setting value

≫

- Torque

Alarm HI limit:

-99999 to 99999 (invalid at 99999 (initial value))

Alarm LO limit:

-99999 to 99999 (invalid at -99999 (initial value))

- Rotation speed

Alarm HI limit:

0 to 99999 (invalid at 99999 (initial value))

Alarm LO limit:

0 to 99999 (invalid at 0 (initial value))

- For initial value, since both the alarm HI and LO limits are invalid as default settings,

set them again for use.

- Since the alarm HI limit and LO limit are independent, simple use of either one of them

is also possible.

■

HI limit, LO limit, alarm HI limit, alarm LO limit

How to set

With ±LOAD, OFL1, or OFL2 on torque, torque HI, LO is forcedly turned on.

With OFL2 on rotation speed, rotation speed HI, LO is forcedly turned on.

Point

SET.

Comp. Setting

Page 1/Page 3

→

Meas. Setting

→

Summary of Contents for TM700




























































































Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands

Unipulse TM700, Operation Manual

Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands