Unipulse TM700 Operation Manual Download Page 53

Page: 53 / 91

SETTING OF FUNCTIONS

F F

TIO

Chapter

5-14.

Waveform Display

■

Graphic screen

Graph is updated while operating on the ordinary display screen (comparison, graph).
One of torque, rotation speed or power status is displayed as a graph. (Selection)
The status before and after triggering can be confirmed by the trigger setting.

Y-axis setting button:

Sets the Y-axis scale.

Trigger setting button:

Goes to the setting screen for trigger.

Indicated value display:

The value specified by torque and graph selection is displayed.
Torque: Torque, Speed
Speed:

Torque, Speed

Power:

Torque, Power

Graph selection button:

Selects the indicated value to be plotted on a graph.
Torque, Speed, Power

Take-in start/stop button:

Starts/stops taking in a graph.

X-axis setting button:

Sets the X-axis scale.

Wave check button:

Goes to the wave check screen.

Trigger mark (X):

The position of X-axis specified by the trigger setting or pre-trigger
value is indicated.

Trigger mark (Y):

The position of Y-axis specified by the trigger setting or trigger
level is indicated.

X-axis setting button

Take-in start/stop button

Y-axis

Indicated value display

setting button

Trigger

setting button

Wave check button

Graph selection button

Trigger mark (X)

Trigger mark (Y)

CAUTION

While the wave check, trigger setting screen or setting screen is opened, the graph
will not be renewed.

Summary of Contents for TM700




























































































Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands

Unipulse TM700, Operation Manual

Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands