Unipulse TM700 Operation Manual Download Page 81

Page: 81 / 91

SUPPLEMENTS

Chapter

■

Speed/power display section

8-2.

Protect/Initialization

■

Measurement setting parameter protection

Set whether to protect the set values in measurement setting from changing.

≪

Setting value

≫

ON, OFF

How to set

■

System setting parameter protection

Set whether to protect the set values in system setting from changing.

≪

Setting value

≫

ON, OFF

How to set

■

Calibration setting parameter protection

→

See "Calibration Protect" on page 17.

How to set

■

Initialization

All the set values of each setting item are initialized to their factory defaults.
Select the setting item you want to initialize.

≪

Setting value

≫

MEAS. Set., System Set., Calibration Set.

* If the setting item on which you intend to execute initialization is protected, initialization cannot

be executed.

How to set

OFL1

Below -99999

The power exceeds the display range.

Check the power unit and decimal place settings.

OFL2

99999

The rotation speed or power exceeds the display range.

On the rotation speed side, check the connection with the
UTM

Ⅱ

, and on the power side, check the power unit and

decimal place settings.

ALM HI

Beyond the alarm HI limit

Rotation speed is at a faster or slower speed than expected.

Confirm that rated rotation speed and rotation are not locked

and so forth.

ALM LO

Below the alarm LO limit

SET.

Page 1

Protect / Init.

→

SET.

Page 1

Protect / Init.

→

SET.

Page 1

Protect / Init.

→

SET.

Page 1

Protect / Init.

→

Summary of Contents for TM700




























































































Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands

Unipulse TM700, Operation Manual

Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands