Tsuruga 8526 Instruction Manual Download Page 66

Page: 66 / 94

Explanation of command

4.2.14

IDNT?

(read-out of tester identification)

Function

Reads out the model name, software version of the tester.

Structure

IDNT?

Transmission

IDNT?



Response

When 8526 received the effective command setting.

IDNT=TSURUGA_8526_ROM-NO.456_Ver.1.00.00



① ②

①

Model name

②

Software version

(For improvement of quality, the software version might have been updated.)

4.2.15

AVOLT=

(setting of test voltage range of AC withstanding voltage test)

Function

Makes the setting of test voltage range of AC withstanding voltage test.

Structure

AVOLT=

Test voltage range

Test voltage range 2.5kV or 5.0kV is to be set

Transmission

AVOLT=5.0kV



…….. Sets the range of AC withstanding voltage test at 5.0kV.

Response

When 8526 received the effective command setting.

ERROR=0



…….……. When the Response Setting is ON.

No response …………….. When the Response Setting is OFF.

4.2.16

AVOLT?

(read-out of test voltage range of AC withstanding voltage test)

Function

Reads out the test voltage range of AC withstanding voltage test.

Structure

AVOLT?

Transmission

AVOLT?



Response

AVOLT=2.5kV



….…. Indicates the test voltage range of AC withstanding voltage

test 2.5kV.

Summary of Contents for 8526































































































Search results

Summary of Contents for 8526

Reviews:

Related manuals for 8526

Brands by name

Popular brands

Tsuruga 8526, Instruction Manual

Search results

Summary of Contents for 8526

Reviews:

Related manuals for 8526

Brands by name

Popular brands