Tsuruga 8526 Instruction Manual Download Page 33

Page: 33 / 94

13. Remote control

On the model

8526

, a remote control is possible through

REMOTE

connector

⑤

on the

front panel,

REMOTE

terminal

REMOTE/OUT

connector

⑱

on the rear panel.

WARNING

When the tester is remote-controlled, high voltage is switched ON/OFF by

the external signal, so utmost care must be taken so that the high voltage

can no be erroneously generated and that no one never touches the output

terminals, high voltage cable or test sample, putting the first priority to safety.

13.1

●

Operation by REMOTE connector

With use of the optional Remote Control Box (Model 5858-07, 07W) connected to the

REMOTE

connector

⑤

, the start/stop operation can be remote-controlled.

When the plug of the remote control box is inserted, the

REMOTE

lamp is lit up and the

type of operation changes from the switch operation on the front panel to the remote
control by the remote control box.
During the remote operation, the

START

switch

③

on the front panel is disabled.

13.2

●

Operation by REMOTE terminal

An equivalent operation to that through

REMOTE

connector

⑤

is also possible

through the

REMOTE

terminal

on the rear panel.

By connecting the optional foot switch (model 5858-04) to the

START

terminal, the start

operation can be done by foot.

①

Turn the power supply OFF and confirm that the

DANGER

lamp

⑩

is turned off.

②

Make a short-circuit between

REAR:ON

and

terminal of the

REMOTE

terminal

Or alternatively, make a short-circuit between the pin No.2 of the

REMOTE/OUT

connector

⑱

and the

COM

(either one of pin No.19, 23 or 36) of the same connector

⑱

③

Connect a logic element such as switch, relay contact, transistor, photo-coupler etc.
between

START

and

, and between

STOP

and

④

Turn ON the power supply and the

REMOTE

lamp at the display section is lit up, then

the remote control is enabled.

Note

: When the remote control is in operation, the

START

switch

③

on the front

panel is disabled. However, the stop operation is still possible from both of the

STOP

switch

②

on the front panel and the STOP terminal of the

REMOTE

terminal

Summary of Contents for 8526































































































Search results

Summary of Contents for 8526

Reviews:

Related manuals for 8526

Brands by name

Popular brands

Tsuruga 8526, Instruction Manual

Search results

Summary of Contents for 8526

Reviews:

Related manuals for 8526

Brands by name

Popular brands