Toyota Solara guide Owner'S Manual Download | Manualshive

Page: 257 / 497

background image

’06 Solara_U (L/O 0502)

274

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

If you cannot shift the selector lever
out of “P” position to other positions
even though the brake pedal is de-
pressed, use the shift lock override but-
ton as follows:

1. Turn the ignition key to “LOCK”

position. Make sure the parking
brake is on.

2. Pry up the cover with a flathead

screwdriver or equivalent.

3. Insert your finger into the hole to

push down the shift lock override
button. You can shift out of “P”
position only while pushing the but-
ton.

4. Shift into “N” position.

5. Insert the cover.

6. Start the engine. For your safety,

keep the brake pedal depressed.

Be sure to have the system checked by
your Toyota dealer as soon as possible.

If the convertible top does not rise or
lower during convertible top control
switch operation, have your vehicle
checked at your Toyota dealer.

If raising the convertible top manually is
unavoidable, see “RAISING THE
CONVERTIBLE TOP MANUALLY”. Then
you should have it checked as soon as
possible at your Toyota dealer.

NOTICE

Do not lower the convertible top
manually. It may cause damage to the
system.

RAISING THE CONVERTIBLE TOP
MANUALLY

1. Lower the side windows, quarter

windows and sun visors.

If the battery is discharged and the win-
dows cannot be lowered, open both doors.

2. Turn the ignition switch to the

“ACC” or “LOCK” position. Open ei-
ther door or wait for 43 seconds be-
fore raising the convertible top
manually.

If you cannot shift automatic
transmission selector lever

If the convertible top does not
rise or lower

carownersmanual.net

carownersmanual.net

«
...
255
256
257
258
259
...
»

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solara guide

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: HALE Pages: 44

Brand: Jackco Pages: 11

Brand: 3SIXT Pages: 12

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: Phonocar Pages: 2

Brand: Jeep Pages: 380

Brand: Quadratec Pages: 12

Brand: BMW Pages: 189

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands