Toyota Solara guide Owner'S Manual Download Page 407

Page: 407 / 497

ADVANCED FUNCTIONS

4. Touch either

switch to

change the size of the area to avoid.

(b) Editing area to avoid

1. Touch the

“Edit”

switch of the “Areas

to Avoid” to display the “Edit Area to
Avoid” screen.

2. To edit an area to avoid, touch the cor-
responding switch.

3. Touch the

“Name”

“Location”

“Area Size”

switch on this screen.

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Search results

Summary of Contents for Solara guide

Reviews:

Brands by name

Popular brands

Toyota Solara guide, Owner'S Manual

Search results

Summary of Contents for Solara guide

Reviews:

Brands by name

Popular brands