manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 262

’06 Solara_U (L/O 0502)

279

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

Check the interior of your vehicle. Wa-
ter and dirt can accumulate under the
floor mats and could cause corrosion. Oc-
casionally check under the mats to make
sure the area is dry. Be particularly care-
ful when transporting chemicals, cleans-
ers, fertilizers, salt,  etc.; these should be
transported in proper containers. If a spill
or leak should occur, immediately clean
and dry the area.

Use mud shields on your wheels. If you
drive on salted or gravel roads, mud
shields help protect your vehicle. Full- size
shields, which come as near to the ground
as possible, are the best. We recommend
that the fittings and the area where the
shields are installed be treated to resist
corrosion. Your Toyota dealer will be
happy to assist in supplying and installing
the shields if they are recommended for
your area.

Keep your vehicle in a well ventilated
garage or a roofed place. Do not park
your vehicle in a damp, poorly venti-
lated garage. If you wash your vehicle in
the garage, or if you drive it covered with
water or snow, your garage may be so
damp as to cause corrosion. Even if your
garage is heated, a wet vehicle can cor-
rode if the ventilation is poor.

Washing your Toyota

Keep your vehicle clean by regular
washing.

The following cases may cause weakness
to the paint or corrosion to the body and
parts. Wash your vehicle as soon as pos-
sible.

When driving in a coastal area

When driving on a road sprinkled with
antifreeze

When exposed to coal tar, tree sap,
bird droppings and carcass of an insect

When driving in areas where there is
a lot of smoke, soot, dust, iron dust or
chemical substances

When the vehicle becomes remarkably
dirty with dust and mud

Hand- washing your Toyota

Work in the shade and wait until the
vehicle body is not hot to the touch.

CAUTION

When cleaning under floor or chassis,
be careful not to injure your hands.

Convertible—For washing instructions for
the convertible top, see “Washing convert-
ible top” on page 281 in this Section.

1. Rinse off loose dirt with a hose. Re-

move any mud or road salt from the
underside of the vehicle or in the
wheel wells.

Washing and waxing your
Toyota

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands