Toyota Solara guide Owner'S Manual Download Page 420

Page: 420 / 497

ADVANCED FUNCTIONS

3. Touch the

“On”

switch of “Guidance

Screen on Freeway” and touch the

“OK”

switch.

Street name on scroll map

When the “Street Name on Scroll Map”
feature is turned on, the system will dis-
play the name of a street where the cursor

is positioned on the scroll map.

To turn the “Street Name on Scroll Map”
mode on:

1. Push the

“MENU”

button.

2. Touch the

“Setup”

switch. Then

touch

switch twice to display page 3 of

the “Setup” screen.

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Search results

Summary of Contents for Solara guide

Reviews:

Brands by name

Popular brands

Toyota Solara guide, Owner'S Manual

Search results

Summary of Contents for Solara guide

Reviews:

Brands by name

Popular brands