Toyota Solara guide Owner'S Manual Download Page 34 | Manualshive

Page: 34 / 497

Toyota Solara guide Owner'S Manual Download Page 34

’06 Solara_U (L/O 0502)

33

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

2. To remove the fuel tank cap, turn

the cap counterclockwise by 90 de-
grees (to the pressure point 1), and
then turn it an additional 30 degrees
(to point 2). Pause slightly before
removing it.

It is not unusual to hear a slight swoosh
when the cap is opened.

3. The removed cap can be stored on

the back side of the fuel filler door.

Position the cap so that the hooks point
to the left and right, and set it in the
receptacle on the back side of the door.

When installing the cap, turn the cap
clockwise until you hear a click. When
you hear the click, the cap is fully
closed.

If the cap is not installed securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely.

The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.

CAUTION

Make sure the cap is installed se-
curely to prevent fuel spillage in
the event of an accident.

Use only a genuine Toyota fuel tank
cap for replacement. It is designed
to regulate fuel tank pressure.

NOTICE

To prevent damage to the cap, apply
force only in the turning direction to
the cap. Do not pull or pry it.

carownersmanual.net

carownersmanual.net

«
...
32
33
34
35
36
...
»

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands