manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 194

’06 Solara_U (L/O 0502)

193

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

“A/C” button

To turn on the air conditioning, press the
“A/C” button. The

 

“A/C” button indicator

will come on. To turn the air conditioning
off, press the button again.

If the “A/C” button indicator flashes, there
is a problem in the air conditioning system
and the air conditioning automatically
shuts off. If this happens, take your ve-
hicle to a Toyota dealer for service.

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands