manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 173

’06 Solara_U (L/O 0502)

172

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

“LOADING”:  The unit is acquiring audio
or program information. Wait until the unit
has received the information.

“OFF AIR”: The channel you selected is
not broadcasting any programming. Select
another channel.

“- - - ”: The channel you selected is no
longer available. Wait for about 2 seconds
until the radio returns to the previous
channel or “CH001”. If it does not change
automatically, select another channel.

The XM Listener Care Center is also
available on the phone, please call (800)
852- 9696 during the following hours:
Monday—Saturday: 7 a.m.—1 a.m.
Sunday: 12 p.m.—12 a.m.

∗

: Use of satellite radio requires XM tuner

and service. Contact your Toyota deal-
er for details.

SCAN

Radio

You can either scan all the frequencies on
a band or scan only the preset stations
for that band.

To scan the preset stations: 
Push and hold the “SCAN” button until
you hear a beep. The radio will tune in
the next preset station up the band, stay
there for 5 seconds, and then move to the
next preset station. To stop scanning,
push this button again.

To scan all the frequencies: 
Quickly push and release the “SCAN” but-
ton. The radio will find the next station up
the station band, stay there for 5 seconds,
and then scan again to the next station.
To stop scanning, push this button again.

XM satellite radio

∗

—

You can either scan the currently selected
channel category or scan only the preset
channels for that band.

To scan the preset channels:
Push and hold the “SCAN” button until
you hear a beep. “SCAN” appears on the
display. The radio will tune in the next
preset channel up the band, stay there for
5 seconds, and then move to the next
preset channel. To stop scanning, push
this button again.

To scan the currently selected channel
category:
Quickly push and release the “SCAN” but-
ton. “SCAN” appears on the display. The
radio will find the next channel in the
same channel category up the band, stay
there for 5 seconds, and then scan again.
To stop scanning, push this button again.

∗

: Use of satellite radio requires XM tuner

and service. Contact your Toyota deal-
er for details.

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands