manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual, Page: 206 / 497

Share
Download
Toyota Solara guide Owner'S Manual Download Page 206

’06 Solara_U (L/O 0502)

223

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

2AZ- FE engine

3MZ- FE engine

The three- way catalytic converter is an
emission control device installed in the
exhaust system.

The purpose is to reduce pollutants in the
exhaust gas.

CAUTION

Keep people and combustible mate-
rials away from the exhaust pipe
while the engine is running. The
exhaust gas is very hot.

Do not drive, idle or park your ve-
hicle over anything that may burn
easily such as grass, leaves, paper
or rags.

NOTICE

A large amount of unburned gases
flowing into the three- way catalytic
converter may cause it to overheat
and create a fire hazard. To prevent
this and other damage, observe the
following precautions:

Use only unleaded gasoline.

Do not drive with an extremely low
fuel level; running out of fuel could
cause the engine to misfire, creat-
ing an excessive load on the three-
way catalytic converter.

Do not allow the engine to run at
idle speed for more than 20 min-
utes.

Avoid racing the engine.

Do not push- start or pull- start your
vehicle.

Do not turn off the ignition while
the vehicle is moving.

Three- way catalytic converters

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments