Home
/
Toyota
/
Solara guide
/
Owner'S Manual

Toyota Solara guide, Owner'S Manual, Page: 117 / 497

Share

Page: 117 / 497

Toyota Solara guide Owner'S Manual Download Page 117

’06 Solara_U (L/O 0502)

116

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

HEADLIGHTS

Manual operation—

To turn on the following lights: Twist
the headlight/turn signal lever knob.

Position 1—Parking, tail, license plate,
side marker and instrument panel lights

Position 2—Headlights and all of the
above

Automatic operation—

To turn on or off the lights automatical-
ly, twist the headlight/turn signal lever
knob to the “AUTO” position when the
ignition key is in the “ON” position.

The headlights and/or all of the lights in
position 1 automatically turn on or off de-
pending on the darkness of the surround-
ings.

Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.

The automatic light control sensor is on
the top of the driver’s side instrument
panel.

Do not place anything on the instrument
panel, and/or do not affix anything on the
windshield to block this sensor.

If you feel that the automatic light control
comes into operation too early or too late,
have the sensor adjusted by your Toyota
dealer.

Headlights and turn signals
(for the U.S.A.)

carownersmanual.net

carownersmanual.net

«
...
115
116
117
118
119
...
»

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments