Toyota Solara guide Owner'S Manual Download Page 209 | Manualshive

Page: 209 / 497

background image

’06 Solara_U (L/O 0502)

226

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

Your engine is fitted with iridium- tipped
spark plugs.

NOTICE

Use only iridium- tipped spark plugs
and do not adjust gaps for your en-
gine performance and smooth drive-
ability.

The tandem master cylinder brake system
is a hydraulic system with two separate
sub- systems. If either sub- system should
fail, the other will still work. However, the
pedal will be harder to press, and your
stopping distance will increase. Also, the
brake system warning light may come on.

CAUTION

Do not drive your vehicle with only a
single brake system. Have your
brakes fixed immediately.

BRAKE BOOSTER

The brake booster uses engine vacuum to
power- assist the brakes. If the engine
should quit while you are driving, you can
bring the vehicle to a stop with normal
pedal pressure. There is enough reserved
vacuum for one or two stops—but no
more!

CAUTION

Do not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up your reserved vacu-
um.

Even if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hard, much harder than nor-
mal. And your braking distance will
increase.

Iridium- tipped spark plugs

Brake system

carownersmanual.net

carownersmanual.net

«
...
207
208
209
210
211
...
»

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solara guide

Brand: Lancia Pages: 191

Brand: EUFAB Pages: 12

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

Brand: Ranger design Pages: 24

TX-STAMP-4-FC04

Brand: Over Armour Offroad Pages: 9

Brand: Mercedes-Benz Pages: 91

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: Demco Pages: 4

Brand: AutoLoc Pages: 6

Brand: Lincoln Pages: 586

Brand: ROADGEAR Pages: 2

CHALLENGER HELLCAT 2017

Brand: Dodge Pages: 484

Hitch-Haul 30110315

Brand: Masterbuilt Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands