manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 447

AUDIO SYSTEM

118

Push “AM·SAT”, “FM” or “DISC” button to
turn on the desired mode.  The selected
mode turns on immediately.

Push these buttons if you want to switch from
one mode to another.

If the disc is not set, the compact disc player
does not turn on.

You can turn off the compact disc player by
ejecting the compact disc.  If the audio system
was previously off, then the entire audio sys-
tem will be turned off when you eject the com-
pact disc.  If the other function was previously
playing, it will come on again.

The switches for radio and compact disc
player operation are displayed on the
function switch display screen when the
audio control mode is selected.  Touch
them lightly and directly on the screen.

The selected switch is highlighted in green or
yellow.

INFORMATION

If the system does not respond to a
touch of a switch, move your finger
away from the screen and then touch
it again.

You cannot operate dimmed
switches.

Wipe off fingerprints on the surface of
the display using a glass cleaning
cloth.

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands