manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual, Page: 241 / 497

Share
Download
Toyota Solara guide Owner'S Manual Download Page 241

’06 Solara_U (L/O 0502)

258

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

Discharged battery

Booster
battery

Jumper cable

Positive terminal
(“+” mark)

Positive
terminal
(“+” mark)

4. Make the cable connections in the or-

der a, b, c, d.

a. Connect the clamp of the positive
(red) jumper cable to the positive (+)
terminal on the discharged battery.

b. Connect the clamp at the other end
of the positive (red) jumper cable to
the positive (+) terminal on the booster
battery.

Discharged battery

Booster
battery

Jumper cable

Negative terminal
(“- ” mark)

c. Connect the clamp of the negative
(black) jumper cable to the negative (- )
terminal on the booster battery.

d. Connect the clamp at the other end
of the negative (black) jumper cable to
a solid, stationary, unpainted, metallic
point of the vehicle with the discharged
battery.

The recommended connecting points
are shown in the following illustrations:

Connecting point for 2AZ- FE engine

Connecting point for 3MZ- FE engine

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments