manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 190

’06 Solara_U (L/O 0502)

189

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

Defogging

The inside of the windshield

For best results, set controls as follows:

Fan speed—Any setting except “OFF”
Temperature—Towards WARM 

(red zone) to heat; 
COLD (blue zone) to
cool

Air intake—FRESH (outside air) 
Air flow—WINDSHIELD

Turning the air flow selector to the wind-
shield position turns on the defogging
function with the purpose of clearing the
front view.

When turning the air flow selector to wind-
shield position, air intake selector mode
changes to FRESH automatically to clean
up the front view quickly. It is not possible
to return to RECIRCULATE in this posi-
tion.

Press the “A/C” button for dehumidified
heating or cooling. This setting clears the
front view more quickly.

On humid days, do not blow cold air
on the windshield—the difference be-
tween the outside and inside tempera-
tures could make the fogging worse.

Defrosting

The outside of the windshield

For best results, set controls as follows:

Fan speed—Any setting except “OFF”
Temperature—Towards WARM 

(red zone) 

Air intake—FRESH (outside air)
Air flow—WINDSHIELD

Turning the air flow selector to the wind-
shield position turns on the defrosting
function with the purpose of clearing the
front view.

When turning the air flow selector to wind-
shield position, air intake selector mode
changes to FRESH automatically to clean
up the front view quickly. It is not possible
to return to RECIRCULATE in this posi-
tion.

Press the “A/C” button for dehumidified
heating. This setting clears the front view
more quickly.

To heat the vehicle interior while de-
frosting the windshield, choose
floor/windshield air flow.

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands