manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 142

’06 Solara_U (L/O 0502)

141

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of “P” position when the
brake pedal is depressed (with the ignition
switch in the “ON” position).

(a) Selector lever

The shift position is also displayed on the
instrument cluster.

P: Parking, engine starting and key

removal

R: Reverse

N: Neutral

D: Normal driving (shifting into overdrive)

S: “S” mode driving

+: Upshift range

- : Downshift range

Automatic transmission

Shift with the brake pedal
depressed. 
(The ignition switch must
be in “ON” position.)

Shift normally.

To select “S” or “D”, lean
the selector lever leftward
or rightward.

Selector lever

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands