manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 122

’06 Solara_U (L/O 0502)

121

2006 SOLARA from Feb. ’05 Prod. (OM33667U)

NOTICE

To prevent the battery from becoming
discharged, do not leave the switch
on longer than necessary when the
engine is not running.

To adjust the brightness of the instru-
ment panel lights, turn the knob.

To turn on the front fog lights, twist
the band of the headlight and turn sig-
nal switch lever. They will come on
only when the headlights are on low
beam.

Instrument panel light control

Front fog lights

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands