manualshive.com logo in svg

Toyota Solara guide, Owner'S Manual

Share
Download
Toyota Solara guide Owner'S Manual Download Page 415

ADVANCED FUNCTIONS

86

3. Touch the 

“Change”

 switch.  The

“Adjust Time Zone” screen appears on the
display.

4. Touch the desired time zone.

The selected switch is highlighted in green.

5. Touch the 

“OK”

 switch on the screen

and the “Setup” screen will be displayed.

Auto voice guidance

When the “Auto Voice Guidance” feature
is turned on, the voice guidance can be
heard automatically.

When the “Auto Voice Guidance” feature
is turned off, the voice guidance can be
heard only if you push the 

“MAP/

VOICE”

 button.

To turn the “Auto Voice Guidance” mode
on:

1. Push the 

“MENU”

 button.

2. Touch the 

“Setup”

 switch.  Then

touch 

 switch to display page 2 of the

“Setup” screen.

carownersmanual.net

carownersmanual.net

Summary of Contents for Solara guide


















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands