Toshiba TC32306FTG Manual Download

Page: 62 / 102

TC32306FTG

2015-10-01

[D5]IFBW [IF Filter Bandwidth]

[D5]IFBW

IF Filter Bandwidth

IF Frequency

320kHz

230kHz

270kHz

280kHz

Change IF Frequency depends on IF Filter Bandwidth.

[D4:D1]BRF_Bit3..0 [Bit Rate Filter Cutoff Frequency]

For details, see Table 6-25.

[D0]

Set to “0” surely.

6.10.7 h’0F RX Function Settings 1

Table 6-62 Register (h’0F)

Name

Drssi_en

Preamble_

Ndet_en

Hdet_en

Dataout_

cnt_en

Digital_en

Det_reset_n

NIR_L2

Initial

Type

R/W

[D7]Drssi_en [RSSI Detection]

0: Disable / 1: Enable

[D6]Preamble_en [Preamble Detection]

0: Disable / 1: Enable

[D5]Ndet_en [Noise Detection]

0: Disable / 1: Enable

[D4] Hdet_en [High Frequency Detector]

In Delay Detection (h'10[D0]Sel_Det = "0"), this register setting is valid.

0: Disable / 1: Enable

[D3]Dataout_cnt_en [DATA_IO Control]

0: Disable / 1: Enable

[D2]Digital_en [Digital Block Control]

Digital Block (Detctor, LPF(ASK), LPF(FSK), BRF, Data COMP) Control

0: Disable / 1: Enable

[D1]Det_reset_n [Detection Reset (RSSI Detection / Noise Detection / Preamble Detection)]

0: Detection Reset (Auto resume)

1: Reset is released

Notice:

These detections are reset after writing all the registers in this address.

The function is resumed automatically at the rising edge of CS signal after setting this register.

TC32306FTG always outputs previous input value of the register whichever the auto resume or not,

(If this register is written to "0", the register outputs "0", after that auto resume.)

Summary of Contents for TC32306FTG







































































































Search results

Summary of Contents for TC32306FTG

Reviews:

Related manuals for TC32306FTG

Brands by name

Popular brands

Toshiba TC32306FTG, Manual

Search results

Summary of Contents for TC32306FTG

Reviews:

Related manuals for TC32306FTG

Brands by name

Popular brands