Toshiba TC32306FTG Manual Download Page 47

Page: 47 / 102

TC32306FTG

2015-10-01

The setup sequence and operation of internal function blocks will start after setting Delay time

from the output level of Reference Clock Oscillator is over a certain level.

Signal Detections (RSSI & Noise Detection) with operating cycle (Initial value: 1.35 ms) set by

Start timing of the demodulation output (from DATA_IO pin) is varied with Bit Rate Filter

setting, data rate or other register settings. Preamble Detection output starts after the

demodulation output is obtained.

Fig 6-29 Example of Boot Sequence Timing Chart (SPI Mode / RX)

* The example of timing chart may be omitted or simplified for explanatory purposes.

Notice:

To shorten the boot sequence of this IC, there is other way to be able to moving to Run without

going through Standby. In this method, firstly set ENB pin = "H", h'0A [D7] ENB = "1" and h'0A

[D6] ACT = "1", then set other registers. But in this way, if the internal setup and the register

setting are overlapped each other, unexpected operation may occur. To avoid above, make the SPI

speed too fast enough to communicate, or select the previous way as in Fig 6-29.

Check the relationship between supply voltage and reset, when to utilize the power on reset

during boot sequence. (See the notice in 6.3.1)

- Example of Boot Sequence 2: TX (in SPI Mode)

The following Fig 6-30 shows status transition from Battery Saving/Standby to TX-Run.

Control Command

（

SPI

）

Internal Regulator

(voltage)

Level of
Reference Clock

Internal Counter

Demodulation Output

: at DATA_IO pin

RESET

Voltage Supply

PLL_LD Signal

: at DET_TMONI1 / 2 pin

Signal Detections

(RSSI / Noise Detection)

: at DET_TMONI1 / 2 pin

ENB

In this example, ENB pin and voltage supply are connected.

h‛

0A[D7]ENB="1",

h‛

0A[D6]ACT="0"

h‛

0A[D7]ENB="1",

h‛

0A[D6]ACT="1"

Settings

105.5

*: Initial Value
It indicates typical.

Starting the system clock
input to logic circuit

Delay Time Setting
* 105.5

s / 211.1

s / 316.5

s / 527.5

s / 949.5

About 0.22ms

Detection Setup

Detection Cycle Setting
0.338ms / 0.675ms / * 1.35ms / 2.70ms

1.35ms

About

0.1ms

Start of the demodulation output depends on Bit
Rate Filter setting or others.

High Impedance

Demodulation Output

Summary of Contents for TC32306FTG







































































































Search results

Summary of Contents for TC32306FTG

Reviews:

Toshiba TC32306FTG, Manual, Page: 47 / 102

Search results

Summary of Contents for TC32306FTG

Reviews: