Toshiba Qosmio G40 Maintenance Manual Download Page 87 | Manualshive

Page: 87 / 458

background image

2.5 USB FDD Troubleshooting

2 Troubleshooting Procedures

Procedure 3

Connector Check and Replacement Check

USB FDD is connected to USB port on system board. The connection of the cable and board
may be defective. Otherwise, they may be faulty. Disassemble the computer following the
steps described in Chapter 4,

Replacement Procedures

and perform the following checks.

USB FDD can be connected to the following 5 ports.
(System board x 4 ports and Sound/USB Jack board x 1 port)

Check 1 Make sure USB FDD is firmly connected to USB port. If the connection is loose,

connect firmly and repeat Procedure 2. If the problem still occurs, go to Check 2.

NOTE:

When checking the connection, be sure to check it with care for the followings.

1. Cable can not be disconnected from the connector.

2. Cable is connected straight to the connector.

3. Cable is connected all the way seated in the connector.

4. Cable or connector can not be broken.

QOSMIO G40 Maintenance Manual (960-632)

[CONFIDENTIAL]

2-41

Downloaded from LpManual.com Manuals

«
...
85
86
87
88
89
...
»

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Qosmio G40

Aspire One AOP531h

Brand: Acer Pages: 12

Brand: Huawei Pages: 28

Brand: Huawei Pages: 41

Brand: Huawei Pages: 39

MateBook HZ-W09

Brand: Huawei Pages: 168

matebook 16s cref-x

Brand: Huawei Pages: 23

Brand: Huawei Pages: 39

Brand: Huawei Pages: 28

Brand: Huawei Pages: 110

Brand: Huawei Pages: 28

Brand: Huawei Pages: 297

Brand: Huawei Pages: 117

Brand: Huawei Pages: 120

Brand: Huawei Pages: 124

20YM0009GE-CAMPUS

Brand: Lenovo Pages: 74

Brand: Lenovo Pages: 64

A215-S6814 - Satellite - Turion 64 X2 2.2 GHz

Brand: Toshiba Pages: 3

A215-S5849 - Satellite - Turion 64 X2 2 GHz

Brand: Toshiba Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands