Toshiba Qosmio G40 Maintenance Manual Download Page 67

Page: 67 / 458

2.4 System Board Troubleshooting

2 Troubleshooting Procedures

Procedure 2

Debugging Port Check

Check the D port status by a debug port test. The tool for debug port test is shown below.

Figure 2-2 A set of tool for debug port test

The test procedures are follows:

Connect the debug port test cable to the connector CN3490 of the system board. For
disassembling to connect the test cable, refer to Chapter 4.

Connect the debug port test cable and RS-232C cross-cable to the test board.

Connect the RS-232C cross-cable to the PC that displays the results.

Boot the computer in MS-DOS mode.

Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for
starting D port into FDD and input “FD starting drive:>dport”.)

The D port status is displayed in the following form;

When the D port status is FFFFh (normal status), go to Procedure 4.

When the D port status falls into any status in Table 2-4, execute Check 1.

QOSMIO G40 Maintenance Manual (960-632)

[CONFIDENTIAL]

2-21

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands