Toshiba Qosmio G40 Maintenance Manual Download Page 249

Page: 249 / 458

4.3 ExpressCard & PC card/Bridge media

4 Replacement Procedures

4.3 ExpressCard & PC card/Bridge media

4.3.1 ExpressCard & PC card

Removing the ExpressCard & PC card

The following describes the procedure for removing the ExpressCard & PC card (See Figure
4-3 and 4-4).

CAUTION: Insert or remove an Express card & PC card in accordance with any

instructions in their manual or the manuals of the computer system you are
using.

Push the

eject button

. It will pop out when you release it. Then press the eject button

once more to eject an ExpressCard or PC card.

Grasp an

ExpressCard

PC card

and remove it.

NOTE: If an ExpressCard or PC card is not inserted all the way, the eject button may

not pop out. Be sure to push an ExpressCard or PC card firmly and press the
eject button again.

[ExpressCard (Upper slot)]

Eject button

ExpressCard

Figure 4-3 Removing the ExpressCard

QOSMIO G40 Maintenance Manual (960-632)

[CONFIDENTIAL]

4-11

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands