manualshive.com logo in svg

Toshiba Qosmio G40, Maintenance Manual

The Toshiba Qosmio G40 is a high-performance laptop designed for multimedia enthusiasts. Discover all the features and functions of this cutting-edge device by accessing its comprehensive User Manual. Download it for free from our website manualshive.com and enhance your experience with this extraordinary laptop.

Share
Download
background image

4 Replacement Procedures 

4.27 GPU heat sink/North bridge heat sink/GPU fan  

Installing the GPU heat sink/North bridge heat sink/GPU fan 

The following describes the procedure for installing the GPU heat sink/North bridge heat 
sink/GPU fan (See Figure 4-49 to 4-51). 

1.

 

When install a new 

GPU fan

, stick a new 

insulator 

on the GPU fan. 

 

GPU fan 

Insulator

Figure 4-51   Sticking a new insulator  

2.

 

If there is already silicon grease on the GPU, clean it with a cloth. 
Using a special applicator, apply silicon grease so that the GPU chip on the GPU is 
completely covered. 

NOTE:  Apply the silicon grease enough to cover the chip surface using the special 

applicator. 

3.

 

Install the 

GPU heat sink

 (with a fan) and 

GPU holder

 and secure them with the 

following 

screws

. 

•

 

M2.0

×

4B 

 BIND 

screw 

    

×

3 

NOTE:  When securing the GPU holder, be sure to secure the screws in the order of the 

number marked on the holder. 

4.

 

Connect the 

GPU fan cable

 from the connector 

CN8781

 on the system board. 

4-70 

[CONFIDENTIAL] 

QOSMIO G40 Maintenance Manual (960-632) 

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Qosmio G40

Panasonic ToughBook CF-72 Series Operating Instructions Manual preview
ToughBook CF-72 Series
Brand: Panasonic Pages: 68
Panasonic Touchbook CF-50 Series Reference Manual preview
Touchbook CF-50 Series
Brand: Panasonic Pages: 56
Panasonic Toughbook CF-T8EWATZJM Reference Manual preview
Toughbook CF-T8EWATZJM
Brand: Panasonic Pages: 133
Panasonic Toughbook CF-T8EWATZJM Operating Instructions Manual preview
Toughbook CF-T8EWATZJM
Brand: Panasonic Pages: 40
Panasonic Toughbook CF-31AGP7B2M Operating Instructions Manual preview
Toughbook CF-31AGP7B2M
Brand: Panasonic Pages: 36
Panasonic Toughbook CF-H1ADBAZCM Reference Manual preview
Toughbook CF-H1ADBAZCM
Brand: Panasonic Pages: 113
XPG XENIA 15 Quick Start Manual preview
XENIA 15
Brand: XPG Pages: 46
MSI 00_1636 User Manual preview
00_1636
Brand: MSI Pages: 80
EUROCOM M190S World Warrior User Manual preview
M190S World Warrior
Brand: EUROCOM Pages: 149
HP 14-dk0 Series Maintenance And Service Manual preview
14-dk0 Series
Brand: HP Pages: 96
HP 14g Maintenance And Service Manual preview
14g
Brand: HP Pages: 126
HP 15-bw0 Series Maintenance And Service Manual preview
15-bw0 Series
Brand: HP Pages: 116
HP 14-ba09 Series User Manual preview
14-ba09 Series
Brand: HP Pages: 70
HP 15 Notebook PC Maintenance And Service Manual preview
15 Notebook PC
Brand: HP Pages: 124
HP 15 TouchSmart Maintenance And Service Manual preview
15 TouchSmart
Brand: HP Pages: 162
HP 14-bs011la User Manual preview
14-bs011la
Brand: HP Pages: 70
HP 14-am100na User Manual preview
14-am100na
Brand: HP Pages: 86
HP 14ct-ca000 Maintenance And Service Manual preview
14ct-ca000
Brand: HP Pages: 62

Brands by name

Popular brands

Load more brands