Toshiba Qosmio G40 Maintenance Manual Download Page 326

Page: 326 / 458

4 Replacement Procedures

4.34 Volume board

Installing the Volume board

The following describes the procedure for installing the volume board (See Figure 4-63 and
4-64).

Turn the

knob

of the volume board 90 degrees in the direction in the figure below.

Install the

volume lens

to the volume board while engaging the

latches

Turn the volume dial 90 degrees in the direction in the figure below and install the

volume dial

to the volume board assembly.

Volume board

Knob

Volume lens

Volume dial

Latch

Figure 4-64 Assembling the volume board assembly

Turn up the

insulator

and install the

volume board assembly

to the cover assembly

with the volume board assembly under the guide.

Secure the volume board assembly with the following

screws

•

M2.5

4B FLAT HEAD screw

Arrange the

volume cable

in place while passing the hole of the insulator.

4-88

[CONFIDENTIAL]

QOSMIO G40 Maintenance Manual (960-632)

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands