Toshiba Qosmio G40 Maintenance Manual Download Page 111

Page: 111 / 458

2.15 Sound Troubleshooting

2 Troubleshooting Procedures

2.15 Sound Troubleshooting

To check if the sound function is malfunctioning or not, follow the troubleshooting procedures
below as instructed.

Procedure 1:   Diagnostic Test Program Execution Check
Procedure 2:   Connector Check
Procedure 3:   Replacement Check

Procedure 1

Diagnostic Test Program Execution Check

Execute the Sound test in Sound Test program disk. Refer to Chapter 3,

Tests and Diagnostics

for more information on how to perform the test program.

If any error is detected by the test, go to Procedure 2.

Procedure 2

Connector Check

The connection of sound system is shown in the following figure.

As the connection may be defective, disassemble the computer and check each connection.

If the problem still occurs, go to Procedure 3.

QOSMIO G40 Maintenance Manual (960-632)

[CONFIDENTIAL] 2-65

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands