Toshiba Qosmio G40 Maintenance Manual Download Page 24

Page: 24 / 458

1 Hardware Overview

1.2 System Block Diagram

1-10

[CONFIDENTIAL]

QOSMIO G40 Maintenance Manual (960-632)

VGA controller

nVIDIA NB8P-GS is mounted.

- VRAM DDR2 256MB/512MB

Wireless LAN card

- One PCI-Ex MiniCard
- Intel Golan b/g or a/b/g/n
- Intel Kedron a/b/g/n
- Supports Wireless Communication SW

TV tuner

Some signals (NTSC, PAL and SECAM) are supported for worldwide use and
MPEG2 hardware encoding function are also supported.

LAN controller (82562 Ekron/82573L Vidalia)ntrols LAN and supports 1000Base-T
(Gigabit Ethernet)/100BASE-TX (Fast Ethernet)/10BASE-T (Ethernet).

MODEM (Askey-made 1456VQL4/FOXCONN-made MRT60M893.02 x 1)

Supported by Azallia MDC 1.5 using the Azallia link.

Other main system chips

•

PSC (Toshiba-made TMP86PM49UG x 1)

•

Clock Generator (IDT 9LPR501)

•

EC/KBC (Renesas-made M306KAFCLRP U0 x 1)

•

Audio AMP (Matsushita-made AN12941A-VF x1)

•

Web Camera(Chicony-made 2.0M pixel(effective 1.92M pixels)

•

Intel Turbo Memory (1GB)

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands