Toshiba Qosmio G40 Maintenance Manual Download Page 339

Page: 339 / 458

4.39

Wireless

LAN antennas/Bluetooth antenna

Replacement Procedures

4.39 Wireless LAN antennas/Bluetooth antenna

Removing the wireless antennas/Bluetooth antenna

The following describes the procedure for removing the wireless antennas/Bluetooth antenna
(See Figure 4-74).

Peel off the

glass tapes

fixing the wireless LAN antenna cables and Bluetooth

antenna cable.

Remove the

wireless LAN antennas

and

Bluetooth antenna

from the LCD cover

while peeling off the

wireless LAN antenna cables

and

Bluetooth antenna cable

from

the double-sided tape.

Wireless LAN antenna (black)

Wireless LAN

antenna (white)

Wireless LAN antenna (gray)
(Only for three antenna model)

Bluetooth antenna

Glass tape

Aluminum tape

Insulator

Acetate tape

Tweeter

Web camera

Internal

microphone

Double-sided tape

Figure 4-74 Removing the wireless LAN antenna/Bluetooth antenna

QOSMIO G40 Maintenance Manual (960-632)

[CONFIDENTIAL]

4-101

Downloaded from LpManual.com Manuals

Summary of Contents for Qosmio G40











































































































































































































































































































































































































































































Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands

Toshiba Qosmio G40, Maintenance Manual

Search results

Summary of Contents for Qosmio G40

Reviews:

Related manuals for Qosmio G40

Brands by name

Popular brands