Home
/
Thermo Scientific
/
ISQ 7000
/
Hardware Manual

Thermo Scientific ISQ 7000, Hardware Manual, Page: 95 / 442

Share

Page: 95 / 442

Thermo Scientific ISQ 7000 Hardware Manual Download Page 95

1

Performing Routine Maintenance

Cleaning the Ion Source Cartridge

Thermo Scientific

ISQ 7000 Hardware Manual

67

Figure 57.

Removing the Advanced EI Ion Source for Cleaning

12. Twist the Vespel cap off the ion source cartridge and remove the filament. You may now

disassemble the Advanced EI ion source and clean or replace individual parts. See

Figure 58.

Advanced EI Ion Source Cartridge

Cleaning the Ion Source Components

1. Clean the repeller, lens 2, ion volume and ion cartridge sleeve according to the guidelines

in

Cleaning Durable Components

2. Clean the insulator, lens 1, and lens 3/RF lens according to

Cleaning Delicate

Note

It is often not necessary to clean the ion cartridge sleeve. If the oxidation is removed

from the exterior of the ion cartridge sleeve during cleaning, it is advisable to heat it in the
GC oven to build up an oxidative layer before inserting the sleeve into the ion source
block. An overly clean sleeve exterior surface can cause welding to the ion source block.

«
...
93
94
95
96
97
...
»

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments