manualshive.com logo in svg

Thermo Scientific ISQ 7000, Hardware Manual, Page: 80 / 442

Share
Download
Thermo Scientific ISQ 7000 Hardware Manual Download Page 80

1

  Performing Routine Maintenance

Cleaning the Ion Source Cartridge

52

ISQ 7000 Hardware Manual

Thermo Scientific

5. Press the blue 

Evacuate

 button on the front of the instrument. When the Evacuate light 

flashes green for approximately 20-30 seconds and turns off, the 

Ready to Open 

light 

turns solid green. At that point, the air has been evacuated from the instrument and it is 
safe to open the vacuum interlock valve. 

6. Loosen and twist the top part of the vacuum interlock handle to allow the entire handle 

to move up and down. This handle controls the interior ball valve, which seals the 
vacuum chamber and protects it from the outside pressure.

Figure 35. 

Evacuating the Instrument

Evacuate 
Button

Vacuum
Interlock
Handle

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments